cfgadm_scsi(1M)
NAME
cfgadm_scsi - SCSI hardware specific commands for cfgadm
SYNOPSIS
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_option] -c
function ap_id...
/usr/sbin/cfgadm [-f] [-y | -n] [-v] [-o hardware_option] -x
hardware_function ap_id...
/usr/sbin/cfgadm [-v] [-a] [-s listing_option] [-o
hardware_option] [-l [ap_id | ap_type ... ]]
/usr/sbin/cfgadm [-v] [-o hardware_option] -t ap_id...
/usr/sbin/cfgadm [-v] [-o hardware_option] -h [ap_id...]
DESCRIPTION
The SCSI hardware specific library /usr/lib/cfgadm/scsi.so.1
provides the functionality for SCSI hot-plugging through the
cfgadm(1M) command. cfgadm operates on attachment points,
which are locations in the system where hardware resources
can be dynamically reconfigured. Refer tocfgadm(1M) for
information regarding attachment points.
For SCSI hot-plugging, each SCSI controller is represented
by an attachment point in the device tree. In addition, each
SCSI device is represented by a dynamic attachment point.
Attachment points are named through ap_ids. Two types of
ap_ids are defined: logical and physical. The physical ap_id
is based on the physical pathname, whereas the logical ap_id
is a shorter more user-friendly name. For SCSI controllers,
the logical ap_id is usually the corresponding disk con-
troller number. For example, a typical logical ap_id would
be c0.
SCSI devices are named relative to the controller ap_id.
Thus if a disk device is attached to controller c0, its
ap_id can be:
c0::dsk/c0t0d0
where dsk/c0t0d0 identifies the specific device. In general,
the device identifier is derived from the corresponding log-
ical link for the device in /dev. For example, a SCSI tape
drive logical ap_id could be c0::rmt/0. Here c0 is the logi-
cal ap_id for the SCSI controller and rmt/0 is derived from
the logical link for the tape drive in /dev/rmt. If an iden-
tifier can not be derived from the link in /dev, a unique
identifier will be assigned to it. For example, if the tape
device has no link in /dev, it can be assigned an ap_id of
the form c0::st3 where st3 is a unique internally generated
identifier.
A simple listing of attachment points in the system will
include attachment points at SCSI controllers but not SCSI
devices. Use the -a flag to the list option (-l) to list
SCSI devices as well. For example:
# cfgadm -l
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
sysctrl0:slot0 cpu/mem connected configured ok
sysctrl0:slot1 sbus-upa connected configured ok
To list SCSI devices in addition to SCSI controllers:
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t14d0 disk connected configured unknown
c0::dsk/c0t11d0 disk connected configured unknown
c0::dsk/c0t8d0 disk connected configured unknown
c0::dsk/c0t0d0 disk connected configured unknown
c0::rmt/0 tape connected configured unknown
sysctrl0:slot0 cpu/mem connected configured ok
sysctrl0:slot1 sbus-upa connected configured ok
Refer to cfgadm(1M) for more information regarding listing
attachment points. The receptacle and occupant state for
attachment points at the SCSI controller have the following
meanings:
empty not applicable
disconnected
bus quiesced (I/O activity on bus is suspended)
connected
bus active
configured
one or more devices on the bus is configured
unconfigured
no device on the bus is configured
The corresponding states for individual SCSI devices are:
empty not applicable
disconnected
bus to which the device is attached is quiesced
connected
bus to which device is attached is active
configured
device is configured
unconfigured
device is not configured
OPTIONS
cfgadm defines several types of operations besides listing
(-l).These operations include testing, (-t), invoking confi-
guration state changes, (-c), invoking hardware specific
functions (-x), and obtaining configuration administration
help messages (-h).
-c function
The following generic commands are defined for the
SCSI hardware specific library:
For SCSI controller attachment points, the following
configuration state change operations are supported:
connect
Unquiesce the SCSI bus.
disconnect
Quiesce the bus (suspend I/O activity on bus).
Incorrect use of this command can cause the sys-
tem to hang. See NOTES.
configure
Configure new devices on SCSI bus.
unconfigure
Unconfigure all devices connected to bus.
The following generic commands are defined for SCSI
devices:
configure
configure a specific device
unconfigure
unconfigure a specific device
-f When used with the disconnect command, forces a
quiesce of the SCSI bus, if supported by hardware.
Incorrect use of this command can cause the system to
hang. See NOTES.
-h ap_id
SCSI specific help can be obtained by using the help
option with any SCSI attachment point.
-o hardware_option
No hardware specific options are currently defined.
-s listing_option
Attachment points of class scsi can be listed by using
the select sub-option. Refer to the cfgadm(1M) man
page for additional information.
-t ap_id
No test commands are available at present.
-x hardware_function
Some of the following commands can only be used with
SCSI controllers and some only with SCSI devices.
In the following, controller_ap_id refers to an ap_id
for a SCSI controller, for example, c0. device_ap_id
refers to an ap_id for a SCSI device, for example:
c0::dsk/c0dt3d0.
The following hardware specific functions are defined:
insert_device controller_ap_id
Add a new device to the SCSI controller,
controller_ap_id.
This command is intended for interactive use
only.
remove_device device_ap_id
Remove device device_ap_id.
This command is intended for interactive use
only.
replace_device device_ap_id
Remove device device_ap_id and replace it with
another device of the same kind.
This command is intended for interactive use
only.
reset_device device_ap_id
Reset device_ap_id.
reset_bus controller_ap_id
Reset bus controller_ap_id without resetting any
devices attached to the bus.
reset_all controller_ap_id
Reset bus controller_ap_id and all devices on
the bus.
EXAMPLES
Example 1: Configuring a Disk
The following command configures a disk attached to con-
troller c0:
# cfgadm -c configure c0::dsk/c0t3d0
Example 2: Unconfiguring a Disk
The following command unconfigures a disk attached to con-
troller c0:
# cfgadm -c unconfigure c0::dsk/c0t3d0
Example 3: Adding a New Device
The following command adds a new device to controller c0:
# cfgadm -x insert_device c0
The system responds with the following:
Adding device to SCSI HBA: /devices/sbus@1f,0/SUNW,fas@e,8800000
This operation will suspend activity on SCSI bus c0
Continue (yes/no)?
Enter:
y
The system responds with the following:
SCSI bus quiesced successfully.
It is now safe to proceed with hotplug operation.
Enter y if operation is complete or n to abort (yes/no)?
Enter:
y
Example 4: Replacing a Device
The following command replaces a device attached to con-
troller c0:
# cfgadm -x replace_device c0::dsk/c0t3d0
The system responds with the following:
Replacing SCSI device: /devices/sbus@1f,0/SUNW,fas@e,8800000/sd@3,0
This operation will suspend activity on SCSI bus: c0
Continue (yes/no)?
Enter:
y
The system responds with the following:
SCSI bus quiesced successfully.
It is now safe to proceed with hotplug operation.
Enter y if operation is complete or n to abort (yes/no)?
Enter:
y
Example 5: Encountering a Mounted File System While Unconfi-
guring a Disk
The following command illustrates encountering a mounted
file system while unconfiguring a disk:
# cfgadm -c unconfigure c1::dsk/c1t0d0
The system responds with the following:
cfgadm: Component system is busy, try again: failed to offline:
/devices/pci@1f,4000/scsi@3,1/sd@1,0
Resource Information
------------------ --------------------------
/dev/dsk/c1t0d0s0 mounted filesystem "/mnt"
FILES
/usr/lib/cfgadm/scsi.so.1
hardware specific library for generic SCSI hot-
plugging
ATTRIBUTES
See attributes(5) for descriptions of the following attri-
butes:
____________________________________________________________
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|_____________________________|_____________________________|
| Availability | SUNWcsl (32-bit) |
|_____________________________|_____________________________|
| | SUNWcslx (64-bit) |
|_____________________________|_____________________________|
SEE ALSO
cfgadm(1M), luxadm(1M), config_admin(3CFGADM),
libcfgadm(3LIB),attributes(5)
NOTES
The disconnect (quiesce) operation is not supported on con-
trollers which control disks containing critical partitions
such as root (/), /usr, swap, or /var. The disconnect opera-
tion should not be attempted on such controllers. Incorrect
usage can result in a system hang and require a reboot.
Hotplugging operations are not supported by all SCSI con-
trollers.
WARNINGS
The connectors on some SCSI devices do not confirm to SCSI
hotplug specifications. Performing hotplug operations on
such devices can cause damage to the hardware on the SCSI
bus. Refer to your hardware manual for additional informa-
tion.
Man(1) output converted with
man2html